A list of the contents of this article:
- 1 、How much is a fully automatic waste carton packing machine?
- 2 、What is a simple carton packing machine worth more than 300 yuan?
- 3 、The binding mode of carton baling machine
- 4 、The auxiliary machine of the waste paper Packer can’t start?
- 5 、Technical parameters of baling machine
How much is a fully automatic waste carton packing machine?
The fully automatic waste carton baler is bundled with tempered iron wire, and the fully automatic baler refers to automatic feeding, automatic compression, automatic bundling, automatic out of the bag, and automatic operation in the whole process. Zhengzhou Xieli 160 automatic waste carton shell baling machine price is more than 200,000, you can go to the factory under the field inspection.
What is a simple carton packing machine worth more than 300 yuan?
What is the simple packing machine for multiple cartons? If it costs more than 300 yuan, it should be a very simple ordinary baler.
The binding mode of carton baling machine
1. Continuous binding mode: there is no need to operate any switch, the machine is constantly bundled according to the set interval, which is suitable for mass production.
two。 Manual binding mode: press the twist switch every time, which is suitable for the situation where the production speed is relatively slow or scattered.
3. Automatic bundling mode: (this series of balers have the most extensive market) have the following operation methods:
a. Ball switch: the ball switch is set on the work table, and the bound object moves on the work table, and it will be automatically bound when it presses the ball switch.
b. Pedal switch: every time you step on the pedal switch, the object is packed.
The auxiliary machine of the waste paper Packer can’t start?
1. The hydraulic oil in the hydraulic system of the carton packing machine is not only the carrier of energy and the medium to transmit energy, but also the oil source of lubricating oil on each friction plane of the hydraulic system. If the lubrication degree of the oil source is not enough, the friction coefficient will increase greatly. Increasing the friction force and increasing the friction strength will increase the temperature of the hydraulic system, thus damaging the life of the hydraulic system and increasing the wear damage. Therefore, the degree of lubrication is an important index of hydraulic oil. 2. If there is water in the hydraulic oil, it will seriously weaken the lubrication performance of the hydraulic oil. If it contains volatile impurities, the hydraulic oil will thicken and produce bubbles, thus affecting the stable operation of the hydraulic transmission system. If it contains acidic or alkaline impurities, it will corrode the metal and reduce the service life of the hydraulic waste paper packaging machine. Therefore, the hydraulic oil should be as pure as possible, which can make the performance of the carton packing machine more stable. Live longer. 3. Generally, if the oil is exposed in the air for a long time, it will oxidize with oxygen and produce some colloid substances. These magazines will block the hydraulic system and affect the normal work of the carton baler. 4. Oil is a kind of flammable liquid, so the flammable point of oil should be increased as much as possible to avoid fire.
Technical parameters of baling machine
Packing speed: 1.5sea/strap
Minimum packing: 60mm
Maximum tightening force: 60Kgs
Maximum packing: any
Packaged PP bandwidth: 5mm-15mm
Power supply: 220V (50/60Hz)
Drive motor: 220V 220W
Packing machine volume: 1490 × 570 × 530mm
Weight of packing machine: 80Kg
The main technical parameters of the classic baling machine, other types are also similar to these parameters.
Suitable for conventional object bundles
Power supply, power: 380V/50HZ 750W/5A
Packing speed: ≤ 2.5s / channel
Table height: 750mm
Frame size: width 800mm * height as needed
Binding form: parallel 1 ~ multi-channel, with a little movement, manual, continuous play, ball switch, pedal switch
Applicable strap: thick (0.555-1.2) mm* wide (912) mm
Electrical configuration: French “TE”, Japanese “OMRON”, “ZIK” electrical appliances
Suitable for conventional object bundles
Power supply, power: 380V 50Hz 5A
Packing speed: ≤ 2.5s / channel
Table height: 750mm
Frame size: W (1070) x H (668) mm external W (800) x H (600) mm customization
Applicable strap: thick (0.55 to 1.2) mm* wide (915) mm
Electrical configuration: LG “PLC” control, French “TE”, Japanese “OMRON”, “ZIK” electrical appliances
Machine weight: 240kg (gross weight) / 200kg (net weight)
The development of professional plastic machinery has led to the development of balers, automatic balers, binding machines, automatic binding machines and other binding machines. Steel belt manual packing machine is a new type of advanced pneumatic packaging machinery. It is mainly used in iron and steel enterprises and non-ferrous metal enterprises to bundle various small sizes of pipes, plates, profiles and other products, and is also suitable for the development of the bundled plastic machinery industry in which all kinds of products are packed in wooden cases. it is necessary to strengthen the “three connections” in the light of China’s national conditions and the basic reality of the existing industry, that is, to associate plastic machinery with the high end of the manufacturing industry and seek the development of high-efficiency industries. It is related to the specific needs of important industries that affect the national economy and people’s lives, and highlights the important mother machine position of plastic machinery in the manufacturing industry. Associate plastic machinery and processed products with the national policy of sustainable development, and realize a series of important contributions that the plastic machinery industry can make to sustainable development and scientific development through the coverage and huge output of the plastic industry. reflect the overall planning and development trend of the green development of the industry. Development contact
According to the current situation of the industry, enterprises should continue to be encouraged to acquire high and new technology by means of joint ventures, cooperation and license transfer, but the phenomenon of foreign capital swallowing domestic enterprises through joint ventures should be prevented. Formulate corresponding policies to encourage enterprises to increase investment in science, technology and products, with emphasis on supporting high-efficiency and energy-saving plastic injection molding machines, balers, winding machines, vacuum packaging machines, lightweight technology and equipment for plastic products, as well as the independent research and development of technologies and equipment such as high-efficiency and low-pollution plastic recycling. Encourage enterprises to apply for enterprise technology centers at all levels, cooperate with scientific research institutions to set up plastic machine research and development institutions, and actively make use of government innovation funds to improve the independent development and innovation ability of domestic enterprises. China’s machinery industry will be invited to climb another high-rise!
Technical parameters: suitable for conventional object bundles
Product concept
The control system of the automatic packing machine is composed of the core control unit PLC and the man-machine interface used for operation. The core control unit is controlled by LG “PLC”. The hydraulic system is the core part of the pressurized packing machine. The reliability of its work directly determines whether the action of the packing machine is normal and reliable, in which the oil temperature control becomes the key of the hydraulic control part of the metal hydraulic packing machine. For mechanical and electrical equipment, automation, intelligence and unitalization make the design thoughtful, and its important parts should be considered. The service life of each product is determined by a core component, which is often the most valuable. For example, the core component of the packing machine is the movement; the core component of the sealing machine is the motor; the core component of the shrinkage machine is the furnace channel; the production of the winding machine has been modularized, and the core components are in each module. The core component of the vacuum packaging machine is the vacuum pump. This is enough to see the high technical requirements of packaging machinery production. 1. The automatic packing machine adopts high-quality material guide pulley to effectively solve the wear of ordinary plastic guide pulley and the clamping problem of PP belt.
two。 A high strength blade with a hardness of 65 is adopted, which greatly improves the ability of cutting band and the life of the blade.
3. The resin caster is used, which is more convenient for mechanical movement, and the caster will not deform under the load for a long time.
4. The aluminum alloy frame is adopted, the body shell is composed of a combined way, and the carton baler can determine the size of the bow frame according to the size of the package.
5. All parts are precision machined by NC processing equipment. The firmness of the parts of the automatic packing machine and the unification of the connection action are well guaranteed. For more instructions on balers, please see other series. First of all, install the packing tape coil according to the fitting diagram and tighten the handle (in the toolbox).
Note: 1. The tape rolls of high 170mm and 190mm should be tightened according to the matching drawing respectively. 2. In order to prevent the tape from being loose, do not disassemble the wrapping paper and rope before installing the tape, and remove it after it is fixed in the reel. Secondly, the middle platform and low platform type first remove the upper limit screw of the triangular bracket with disc, correct the brake rod, and then install the limit screw back. Then insert the bracket into the slot on the right side of the rack, tighten the screws, and put on the belt reel. Pass the lead through the rewind pulley A → rewind piece → rewind wheel B until you see the lead go out of the machine table.
Third, the packing machine platform type open the left door, put the belt reel, and then open the right door, take the lead through the guide pulley A → rewind pulley B, then pass the lead through the lower hole of the right door, close the right door, and then take the lead through the hole on the right door of the → (4) → rewind pulley C → rewind piece → rewind pulley D, until you see the lead through the introduction plate. Fourth, after the operation is completed, the baler turns on the “power switch” on the front board of the machine, and the ironing temperature has reached the working requirements after about one minute. Turn on the “power switch” and the bundling work can begin.
Fifth, in order to ensure the safety of the operator, the baler machine must be connected to the protective ground wire PE. If there is leakage, be sure to check whether the power outlet is connected to the protective bottom line to prevent electric shock.
Sixth, the lack of temperature should adjust the “temperature controller” (that is, the knob on the ironing transformer), the right-hand rotation of the baler can increase the ironing temperature, and the left-hand rotation can lower the temperature.
Seventh, adjust the “belt length regulator” on the front plate according to the volume size of the bundles. Each box represents the belt feeding time (seconds). Do not put it at 0 and do not send the tape.
Eighth, if the temporary tape is not long enough, you can press the “manual out” button to feed the belt at will, and put it by hand.
Ninth, this machine is equipped with an automatic stop device, and the downtime can be set by yourself. Finally, if the end of the tie is not flat, press the “manual undo, cut” button to carry on the leg belt, press the hand immediately and cut the belt automatically. It should be noted that non-technical personnel shall not disassemble or loosen at will except the adjustment parts instructed in this manual, especially the red paint parts of the baling machine.
How to adjust the baler?
1. Belt width and seam adjustment when the width of the belt is uneven or the belt of another width must be changed, it is difficult to insert the belt when the left and right slot is too narrow; if it is too wide, the joint of the back belt of the baler will be uneven. Generally speaking, the width of the slot should be about 0.5-1 mm wider than the width of the belt.
2. Baling machine ironing temperature adjustment of the ironing temperature has a great influence on the quality of the belt joint. In order to make the polypropylene strapping joint stick firmly, the knob is generally placed in the 3-5 gear position. Whether the perm temperature is appropriate, you can check the adhesion of the perm surface. If there is a white mark on the surface of the perm, the temperature has been on the high side; if the surface of the perm is wet, the temperature is insufficient.
3. The bundling and loosening adjustment of the bundles of the Packer open the table panel and loosen the inner hexagonal fastening screw on the top of Da Luomu A by hand, which is tight in the clockwise direction and loose on the contrary. After the binding force is moderate, tighten the inner hexagonal setting screw.
4. belt length adjustment the length of the belt is determined by the belt length regulator on the front panel. If the belt is too short, it is easy to tie the hands. At this time, the Packer can grab the lead and pull the belt out along the feeding direction. However, the length of the belt needs to be re-adjusted to ensure that the next binding can be carried out normally. Baler if the belt is too long, it is not easy to align the position, the baler and Panasonic straps are easy to be wound together to cause the straps to be misaligned or broken. Maintenance of baler: 1. Keep the interior of the machine clean and dry at all times. two。 It is easy to place wet or dirty objects on the machine table. 3. Avoid rolling the power cord and roll it when not in use. 4. To maintain the normal operation of the machine, choose the raw material binding tape. The daily maintenance of the baler needs to do the following six points:
(1) remove shavings or dirt from the machine once a week.
(2) once a month, the cleaning and maintenance of the upper skateboard, the middle knife and the front top knife mentioned in the previous section shall be done once a month.
(3) add some lubricating oil to all (shafts, cores) and bearings once every three months after the above two maintenance has been done.
(4) replenish the oil in the gear box of the reducer every two years.
(5) it should be noted that several parts can not be refueled: send and return belt rollers. All the belts. Slip piece and surrounding area.
(6) do not add too much each time to refuel, so as to avoid the failure of the microswitch due to oil immersion. In the early 1960s, with the emergence of polypropylene material, polypropylene plastic belt packing machine was successfully developed abroad, which gradually replaced steel belt binding in many fields, especially in light industry, so that the packing machine was rapidly popularized.
China’s automatic packing machine began to develop in the mid-1980s and was initially popularized in the distribution departments of books, newspapers and periodicals, but it has developed rapidly in recent years. It has been widely used in light industry, food, foreign trade, department stores, printing, medicine, chemical industry, post and telecommunications, textile and other industries.
At the present stage, by adopting international standards and absorbing foreign advanced technical features, some manufacturers of baling machines have made great improvements in terms of standard level, design and manufacturing technology and product quality, such as the fully automatic unmanned baling machine of Yongchuang Machinery. In terms of quality, it has reached the advanced level of similar equipment abroad, and it can be automatically positioned, bundled and transposed to carry out cross-shaped, well-shaped and other pattern binding, using microcomputer control. An unmanned automatic binding production line has been realized. The future development trend of balers extends to full automation, advanced and diversification.
The development trend of balers is mainly manifested in the development of balers for various purposes, such as compression balers, heavy belts and polyester belts instead of steel strips, foam belts and soft belts suitable for desktop baling machines. Improve the degree of automation of the single machine so that after the package is sent from the conveying device, the packing machine automatically locates, binds, transposes, and binds with cross shape, well shape and other patterns; microcomputer control is adopted to realize the automatic binding production line which is unmanned. Foreign automatic balers have been developed to the goal of 40 channels / min to 60 channels / min, and randomly adjusted balers are developed to improve the adaptability of automatic balers in bandwidth, bundling specifications, workbench height, binding capacity and so on. 1. Please confirm the power supply used by the machine and do not plug in the wrong power supply. This machine adopts three-phase four-wire system. The flowered wire is grounded zero wire, which is used for leakage protection.
two。 Do not cross the runway of the belt during operation.
3. Please do not touch the heater directly with your hands.
4. Do not wash the machine with water. When the workplace is wet, operators should not work barefoot.
5. Please reel the tape in the storage compartment back to the reel when the machine is not in use to avoid deformation the next time you use it.
6. Do not stick oil on the surface of the belt roller.
7. Remember to unplug the power supply when the machine is not in use.
8. Do not change the parts on the machine at will.
9. The main parts should always be lubricated with oil.
This is the end of the introduction of carton balers and carton balers. I wonder if you have found the information you need. If you want to know more about this, remember to collect and follow this site.