A list of the contents of this article:
- 1 、How to use the automatic binding machine
- 2 、How does the automatic strapping machine pack?
- 3 、What are the common faults and solutions of automatic binding machine
- 4 、Common faults of automatic packing machine and their solutions
How to use the automatic binding machine
Automatic binding machine refers to a machine that uses packing tape to wind a product or package, then tightens and connects both ends through thermal effect melting or using materials such as clasps. The function of the baling machine is to make the plastic belt cling to the surface of the package to ensure that the package will not be scattered because of poor packing during transportation and storage, and at the same time it should be packed neatly and beautifully. With the repeated use of the automatic binding machine, no matter how durable the automatic binding machine will be more or less wear and failure, what we need to solve is how to deal with the common failures of the automatic binding machine. The following are the common faults and solutions of the automatic binding machine summarized by the editor. I hope I can help you.
Practical information! Common faults of automatic binding machine and their solutions
Photo Source: Internet
First, the bonding effect is not good
1. The heating temperature is too high or too low. Solution: heating temperature is too high or too low.
2. The heating piece is deformed. Solution: correct or replace the heater.
3. The top pressure of the middle top knife is not enough, and the spring in the body is broken. Solution: replace the spring in the middle top knife.
Second, the conveyor belt is not in place
1. The lever pull spring force is too big or too small. Solution: adjust the roller pressure properly.
2. The position of the ejector is too high. Solution: adjust the position of the ejector rod properly.
3. The storage capacity in the belt warehouse is small. Solution: adjust the storage capacity appropriately.
4. The lead splitting leads to poor operation in the belt. Solution: appropriate high-speed fastening force.
5. the belt probe is adjusted too early or too late. Solution: adjust the belt conveyor probe properly.
6. The stop probe is adjusted too far. Solution: adjust the stop probe to the direction of the belt probe for a certain distance.
7. The quality of packing tape. Solution: replace the packing belt.
Third, it can’t be tied up tightly
1. Tighten and adjust the loose position of the installation plate. Solution: adjust the binding force properly.
2. The wear of the tape block is large. Solution: replace the cassette block.
3. The teeth of the tape block are stuffed with shavings. Solution: clean up the shavings.
4. The pull spring of the pull rod is broken. Solution: replace the pull spring.
5. The pendulum rod drives the bearing to break. Solution: replace the bearing.
6. The torsion spring is broken. Solution: replace the torsion spring.
IV. Enlarge the circle
1. There is not enough time to unwind. Solution: adjust the unwinding time.
2. The clearance of the pulley is not correct (too big or too small). Solution: appropriate high-speed unwinding gap.
3. The fastening resistance is too large. Solution: check and clean the frame strap.
4. The motor belt is too loose. Solution: replace or adjust the belt tightness properly.
5. Fault with warehouse volume
1. Friction between the crossbar and the belt. Solution: adjust the clearance between the crossbar and the belt.
2. The position of the proximity switch is incorrect or broken. Solution: check and replace the proximity switch.
3. The pulley force is too small or too large. Solution: adjust the pulley pressure properly.
4. The spring is broken. Solution: replace the tension spring.
5. The pulling force of the spring is too small or too big. Solution: adjust the strength of the spring properly.
6. Brake failure with disc. Workaround: replace the PLC.
7. PLC is bad. Solution: check and replace the corresponding parts, such as brake belt, spring.
8. Too much or too little storage belt. Solution: adjust the storage capacity appropriately.
How does the automatic strapping machine pack?
Automatic binding machine refers to a machine that uses packing tape to wind a product or package, then tightens and connects both ends through thermal effect melting or using materials such as clasps. The function of the baling machine is to make the plastic belt cling to the surface of the package to ensure that the package will not be scattered because of poor packing during transportation and storage, and at the same time it should be packed neatly and beautifully. With the repeated use of the automatic binding machine, no matter how durable the automatic binding machine will be more or less wear and failure, what we need to solve is how to deal with the common failures of the automatic binding machine. The following are the common faults and solutions of the automatic binding machine summarized by the editor. I hope I can help you.
Practical information! Common faults of automatic binding machine and their solutions
Photo Source: Internet
First, the bonding effect is not good
1. The heating temperature is too high or too low. Solution: heating temperature is too high or too low.
2. The heating piece is deformed. Solution: correct or replace the heater.
3. The top pressure of the middle top knife is not enough, and the spring in the body is broken. Solution: replace the spring in the middle top knife.
Second, the conveyor belt is not in place
1. The lever pull spring force is too big or too small. Solution: adjust the roller pressure properly.
2. The position of the ejector is too high. Solution: adjust the position of the ejector rod properly.
3. The storage capacity in the belt warehouse is small. Solution: adjust the storage capacity appropriately.
4. The lead splitting leads to poor operation in the belt. Solution: appropriate high-speed fastening force.
5. the belt probe is adjusted too early or too late. Solution: adjust the belt conveyor probe properly.
6. The stop probe is adjusted too far. Solution: adjust the stop probe to the direction of the belt probe for a certain distance.
7. The quality of packing tape. Solution: replace the packing belt.
Third, it can’t be tied up tightly
1. Tighten and adjust the loose position of the installation plate. Solution: adjust the binding force properly.
2. The wear of the tape block is large. Solution: replace the cassette block.
3. The teeth of the tape block are stuffed with shavings. Solution: clean up the shavings.
4. The pull spring of the pull rod is broken. Solution: replace the pull spring.
5. The pendulum rod drives the bearing to break. Solution: replace the bearing.
6. The torsion spring is broken. Solution: replace the torsion spring.
IV. Enlarge the circle
1. There is not enough time to unwind. Solution: adjust the unwinding time.
2. The clearance of the pulley is not correct (too big or too small). Solution: appropriate high-speed unwinding gap.
3. The fastening resistance is too large. Solution: check and clean the frame strap.
4. The motor belt is too loose. Solution: replace or adjust the belt tightness properly.
5. Fault with warehouse volume
1. Friction between the crossbar and the belt. Solution: adjust the clearance between the crossbar and the belt.
2. The position of the proximity switch is incorrect or broken. Solution: check and replace the proximity switch.
3. The pulley force is too small or too large. Solution: adjust the pulley pressure properly.
4. The spring is broken. Solution: replace the tension spring.
5. The pulling force of the spring is too small or too big. Solution: adjust the strength of the spring properly.
6. Brake failure with disc. Workaround: replace the PLC.
7. PLC is bad. Solution: check and replace the corresponding parts, such as brake belt, spring.
8. Too much or too little storage belt. Solution: adjust the storage capacity appropriately.
What are the common faults and solutions of automatic binding machine
Automatic binding machine refers to a machine that uses packing tape to wind a product or package, then tightens and connects both ends through thermal effect melting or using materials such as clasps. The function of the baling machine is to make the plastic belt cling to the surface of the package to ensure that the package will not be scattered because of poor packing during transportation and storage, and at the same time it should be packed neatly and beautifully. With the repeated use of the automatic binding machine, no matter how durable the automatic binding machine will be more or less wear and failure, what we need to solve is how to deal with the common failures of the automatic binding machine. The following are the common faults and solutions of the automatic binding machine summarized by the editor. I hope I can help you.
Practical information! Common faults of automatic binding machine and their solutions
Photo Source: Internet
First, the bonding effect is not good
1. The heating temperature is too high or too low. Solution: heating temperature is too high or too low.
2. The heating piece is deformed. Solution: correct or replace the heater.
3. The top pressure of the middle top knife is not enough, and the spring in the body is broken. Solution: replace the spring in the middle top knife.
Second, the conveyor belt is not in place
1. The lever pull spring force is too big or too small. Solution: adjust the roller pressure properly.
2. The position of the ejector is too high. Solution: adjust the position of the ejector rod properly.
3. The storage capacity in the belt warehouse is small. Solution: adjust the storage capacity appropriately.
4. The lead splitting leads to poor operation in the belt. Solution: appropriate high-speed fastening force.
5. the belt probe is adjusted too early or too late. Solution: adjust the belt conveyor probe properly.
6. The stop probe is adjusted too far. Solution: adjust the stop probe to the direction of the belt probe for a certain distance.
7. The quality of packing tape. Solution: replace the packing belt.
Third, it can’t be tied up tightly
1. Tighten and adjust the loose position of the installation plate. Solution: adjust the binding force properly.
2. The wear of the tape block is large. Solution: replace the cassette block.
3. The teeth of the tape block are stuffed with shavings. Solution: clean up the shavings.
4. The pull spring of the pull rod is broken. Solution: replace the pull spring.
5. The pendulum rod drives the bearing to break. Solution: replace the bearing.
6. The torsion spring is broken. Solution: replace the torsion spring.
IV. Enlarge the circle
1. There is not enough time to unwind. Solution: adjust the unwinding time.
2. The clearance of the pulley is not correct (too big or too small). Solution: appropriate high-speed unwinding gap.
3. The fastening resistance is too large. Solution: check and clean the frame strap.
4. The motor belt is too loose. Solution: replace or adjust the belt tightness properly.
5. Fault with warehouse volume
1. Friction between the crossbar and the belt. Solution: adjust the clearance between the crossbar and the belt.
2. The position of the proximity switch is incorrect or broken. Solution: check and replace the proximity switch.
3. The pulley force is too small or too large. Solution: adjust the pulley pressure properly.
4. The spring is broken. Solution: replace the tension spring.
5. The pulling force of the spring is too small or too big. Solution: adjust the strength of the spring properly.
6. Brake failure with disc. Workaround: replace the PLC.
7. PLC is bad. Solution: check and replace the corresponding parts, such as brake belt, spring.
8. Too much or too little storage belt. Solution: adjust the storage capacity appropriately.
Common faults of automatic packing machine and their solutions
Automatic binding machine refers to a machine that uses packing tape to wind a product or package, then tightens and connects both ends through thermal effect melting or using materials such as clasps. The function of the baling machine is to make the plastic belt cling to the surface of the package to ensure that the package will not be scattered because of poor packing during transportation and storage, and at the same time it should be packed neatly and beautifully. With the repeated use of the automatic binding machine, no matter how durable the automatic binding machine will be more or less wear and failure, what we need to solve is how to deal with the common failures of the automatic binding machine. The following are the common faults and solutions of the automatic binding machine summarized by the editor. I hope I can help you.
Practical information! Common faults of automatic binding machine and their solutions
Photo Source: Internet
First, the bonding effect is not good
1. The heating temperature is too high or too low. Solution: heating temperature is too high or too low.
2. The heating piece is deformed. Solution: correct or replace the heater.
3. The top pressure of the middle top knife is not enough, and the spring in the body is broken. Solution: replace the spring in the middle top knife.
Second, the conveyor belt is not in place
1. The lever pull spring force is too big or too small. Solution: adjust the roller pressure properly.
2. The position of the ejector is too high. Solution: adjust the position of the ejector rod properly.
3. The storage capacity in the belt warehouse is small. Solution: adjust the storage capacity appropriately.
4. The lead splitting leads to poor operation in the belt. Solution: appropriate high-speed fastening force.
5. the belt probe is adjusted too early or too late. Solution: adjust the belt conveyor probe properly.
6. The stop probe is adjusted too far. Solution: adjust the stop probe to the direction of the belt probe for a certain distance.
7. The quality of packing tape. Solution: replace the packing belt.
Third, it can’t be tied up tightly
1. Tighten and adjust the loose position of the installation plate. Solution: adjust the binding force properly.
2. The wear of the tape block is large. Solution: replace the cassette block.
3. The teeth of the tape block are stuffed with shavings. Solution: clean up the shavings.
4. The pull spring of the pull rod is broken. Solution: replace the pull spring.
5. The pendulum rod drives the bearing to break. Solution: replace the bearing.
6. The torsion spring is broken. Solution: replace the torsion spring.
IV. Enlarge the circle
1. There is not enough time to unwind. Solution: adjust the unwinding time.
2. The clearance of the pulley is not correct (too big or too small). Solution: appropriate high-speed unwinding gap.
3. The fastening resistance is too large. Solution: check and clean the frame strap.
4. The motor belt is too loose. Solution: replace or adjust the belt tightness properly.
5. Fault with warehouse volume
1. Friction between the crossbar and the belt. Solution: adjust the clearance between the crossbar and the belt.
2. The position of the proximity switch is incorrect or broken. Solution: check and replace the proximity switch.
3. The pulley force is too small or too large. Solution: adjust the pulley pressure properly.
4. The spring is broken. Solution: replace the tension spring.
5. The pulling force of the spring is too small or too big. Solution: adjust the strength of the spring properly.
6. Brake failure with disc. Workaround: replace the PLC.
7. PLC is bad. Solution: check and replace the corresponding parts, such as brake belt, spring.
8. Too much or too little storage belt. Solution: adjust the storage capacity appropriately.
This is the end of the introduction on the price of automatic packing machine binding machine and automatic packing machine binding machine. I wonder if you have found the information you need? If you want to know more about this, remember to collect and follow this site.