A list of the contents of this article:
- 1 、Barreled water automatic bagging machine cutting continuous film?
- 2 、I want to set up a small barreled water production line in the countryside with an output of about 100 barrels a day. What kind of equipment do you need?
- 3 、What equipment is needed to produce barreled water?
- 4 、Which brand of bottled water equipment is the best in China?
Barreled water automatic bagging machine cutting continuous film?
If the barreled water automatic bagging machine cuts the film continuously, there may be something wrong with his setting. You need to reset it. Its coefficient can solve this problem.
I want to set up a small barreled water production line in the countryside with an output of about 100 barrels a day. What kind of equipment do you need?
The price varies according to your specific needs.
Generally speaking, the production of barreled water according to your water quality needs raw water treatment equipment, bottled water filling equipment, filling aseptic workshop, etc.
Raw water treatment equipment includes: raw water tank-booster pump-quartz sand filter-activated carbon filter-security filter-reverse osmosis membrane-ultraviolet sterilizer-ozone sterilizer barreled water
The fully automatic filling line includes: automatic capping machine-automatic bucket brushing machine-automatic bottle feeding machine-automatic filling machine-automatic lamp inspection and film collecting machine-fully automatic bucket bagging machine plant area does not need a large equipment and warehouse, fully automatic equipment does not need a few manual operation, but this is only production equipment. Does not include the construction equipment of the aseptic workshop and the laboratory equipment of the waterworks. If you want to run a pure water plant of a certain scale, you also need “health permit”, “production permit”, “environmental protection permit”, “health inspection of employees”, “industrial and commercial registration”, “tax registration” and other relevant documents.
Henan Wanda environmental protection engineering equipment provides a full set of water plant production equipment, including raw water treatment equipment, barreled water automatic filling line, filling aseptic workshop construction and decoration. The effluent of the equipment meets the corresponding national standards, and the output can be more than 200002000 barrels per hour.
Your tailor-made equipment uses quantitative frequency conversion filling system to save water and electricity and has higher efficiency. Optional stainless steel conveying chain plate is strong and durable, running smoothly without damaging the bucket. Barrel body cleaning machine 365 degrees no dead angle cleaning, multi-directional umbrella spray in place, surveillance cameras intelligent identification lid, film, automatic detection is stable and efficient. The fuselage equipment adopts inflatable swing welding: the one-sided welding of the weld is formed on both sides, and the inner surface is formed smoothly, which prevents the sanitary dead angle and the breeding of microorganisms, and can strengthen the corrosion resistance of the weld. all stainless steel equipment left the factory are inflatable swing welding. endoscope photos can be provided.
What equipment is needed to produce barreled water?
1. Raw water purification water treatment system
2. Pretreatment system
3. Quartz sand filter
4. Activated carbon treatment tank
5. Dosing system or softener
Water intake and environmental requirements of reverse osmosis equipment
Power supply: 380V 50Hz
Water supply: 3.0m3/h
Water intake requirements:
Influent temperature: 5-45 ℃
Influent PH: 3.0-10.0
Influent SDI (15 minutes) 5
Free residual chlorine concentration 0.1ppm
The equipment should be placed indoors so as not to accelerate the aging of mechanical parts of the equipment. Influent turbidity 2NTU
The location of the equipment shall be provided with a drain. The largest displacement is 1.5T/H.
The location of the equipment shall be provided with lighting facilities for operation.
Where the equipment is located, there should be sufficient operating space for operation and maintenance. Equipment, should avoid contact with corrosive fumes.
II. Equipment operation
Power on
1. Check the electrical appliances and pipelines to make sure there is water in the original water tank
2. Turn on the water source switch before the incoming water solenoid valve
3. Open [flushing solenoid valve / automatic], [original pump / automatic], [high pressure pump / automatic], [total power supply / ON].
4. The system starts to run automatically
Power off:
Open [flush solenoid valve / manual] and flush for 2 minutes.
Call [main power / off]
Hit [flush solenoid valve / automatic]
Manual flushing of reverse osmosis membrane: flushing: make sure there is water in the original water tank and replenish it, open [flush solenoid valve / manual]
Rotate to [raw pump / manual] [high pressure pump / manual]
After flushing for an appropriate time, rotate to [original pump / stop] [high pressure pump / stop] [flush solenoid valve / stop reverse osmosis valve adjustment:
The flow rate and pressure of the reverse osmosis system have certain requirements, and the equipment should be adjusted to the appropriate state according to the requirements to make the reverse osmosis system operate stably, which only needs to be adjusted once, and the manual valve opening can be kept unchanged in the future.
1. Check the electrical appliances and pipelines to make sure there is water in the original water tank
2. Turn on the water source switch before the incoming water solenoid valve
3. Ball valve, concentrated water discharge valve and closed backflow valve after full opening of RO high pressure pump.
4. Turn on [original pump / manual], [high pressure pump / manual], [total power supply / ON].
5. The RO system starts to run
6. adjustment of the pressure switch in front of the high-pressure pump: the pressure switch in front of the high-pressure pump mainly prevents damage to the equipment caused by the operation of the high-pressure pump when the incoming water pressure is not enough. Adjust the pressure switch in front of the high-pressure pump to 0.5kg/cm2, and close the valve after the high-pressure pump properly, so that the high-pressure pump does not start frequently.
7. Adjust the concentrated water discharge valve (turn off) the reverse osmosis membrane [influent pressure] is about 0.8–1Mpa, the concentrated water flow rate is about 0.6m3/h, and the pure water flow rate is about 1.5m3/h. Adjust the backwater valve so that the concentrated water flow rate is about 0.6-1.0m3/h, and the [inlet pressure] is about 0.8–1Mpa. (when the drainage is all available, it is recommended to close the backwater valve, which is beneficial to increase the life of the membrane.
Automatic control process of reverse osmosis main system:
Process indication: when all the buttons are turned on to the automatic gear, the equipment will follow the following procedure:
When starting, the original hydropower solenoid valve and flushing solenoid valve are all open, the high pressure pump is opened after 5 seconds delay, after flushing for 30 seconds, the flushing solenoid valve is closed, and the system enters the normal water supply state.
When the system is connected with pure water high-level control (floating ball switch), the system automatically opens the flushing solenoid valve and closes the high-pressure pump when the water is full, and closes the original pump and inlet solenoid valve after flushing at low pressure for 20 seconds. When there is water in the original water tank and when the pure water tank is low, automatically open the original water pump, high-pressure pump and water intake magnetic valve to make water.
When the current treatment system flushes or regenerates automatically, the high pressure pump stops and the water and electricity magnetic valve is turned off.
Fourth, pre-processing operation panel description
A1-intake valve A2-outlet valve A3-backwash intake valve A4-backwash drain valve A5-positive wash drain valve
(1) Sand filter
1. Specification: φ 400 × SS1650
2. Quantity: 1
3. Material: FRP
4. Type of filter media: refined quartz sand
Function: effectively remove suspended solids and impurities in water and reduce influent turbidity.
Method of operation: the pipe valve arrangement of the sand filter is shown in figure 2.
(1) run
When starting normally, first open the intake valve A1 and the positive washing discharge valve A5, control the inlet water flow at 1.0T/H, gradually open the outlet valve A2 after 3-5 minutes of operation, close the positive washing discharge valve A5, and then the sand filter enters normal operation.
(2) backwashing
With the increase of the running time of the pure water machine, the intercepted dirt gradually increases and the flow resistance becomes larger, so backwashing should be carried out to restore the filtration capacity of the sand filter. First open the backwash drain valve A4 and the backwash intake valve A3, the backwash flow rate is controlled at about 1-2T/H, backwash for 5 minutes (depending on the pollution blockage), flush out the sundries and bubbles in the filter material until the effluent is clear.
(3) after positive washing and reverse washing, open intake valve A1 and positive washing discharge valve A5, control flow 1T/H, and wash until the effluent is clear and qualified (about 3 minutes). Open the outlet valve A2 and close the positive washing drain valve A5 and transfer to the normal working state. (2) carbon filter
1. Specification: φ 400 × SS1650
2. Quantity: 1
3. Material: FRP
4. Type of filter media: water purification grade coconut shell activated carbon
Function: effectively remove the organic matter and residual chlorine in the water.
How to operate: the pipe valve of the carbon filter is arranged as shown in the figure above. The operation method is the same as that of sand filter.
Fifth, pre-treatment flushing cycle setting:
Sand column: once a day
Carbon column: once every 3 days
Filter element replacement: depending on the pollution, generally 1-2 weeks.
Daily replacement of 5 μ m PP filter element and carbon core:
In order to ensure the normal operation of the reverse osmosis system and prolong the service life of the RO membrane, the PP filter element with a pore diameter of 5 μ m is used in this system, which has the characteristics of high filtration accuracy and long service life. The replacement period is generally one week according to the water quality, and the replacement condition is that the filter element is seriously polluted in a large area, blackening and yellowing.
The service life of the filter element is directly related to the operation status of the pretreatment equipment. The good operation of the pretreatment equipment can remove most of the solid particles, flocculent precipitation and organic matter, reduce the load of the microfilter and prolong the service life of the filter element.
The filter element should be replaced regularly to ensure its interception, otherwise it may cause irreparable loss to the RO film.
Which brand of bottled water equipment is the best in China?
Bottled water should not only choose a brand. Also choose the place of origin, big brands due to freight problems, are produced locally, such as Yibao, Nongfu Mountain Spring, Robust, Wa. Wait,
For small brands, it depends on their strength.
However, it is recommended to buy a big brand.
This is the end of the introduction of barrel bagging machine and barrel bagging machine. I wonder if you have found the information you need? If you want to know more about this, remember to collect and follow this site.