A list of the contents of this article:
- 1 、How to use the tape paper sealer
- 2 、How to use transparent tape cutter, box sealer, packing machine
- 3 、How to use the tape packing machine
- 4 、Operation method of adhesive Tape sealing Machine
- 5 、How to load the adhesive tape in the sealing machine? How to adjust the length?
How to use the tape paper sealer
The box sealer is generally used to seal the box or to cut the tape.
1. First hold the box sealer in hand, then open the back cover of the box seal, pull it up and open it.
two。 Then take the tape, first tear the tape open and stretch it out, as shown in the picture, then put the tape into the cylinder and put the tape head on the pulley.
3. After installing the tape, you need to learn to use it, put your finger in the cylinder and gently press the back cover of the box sealer with your thumb.
4. Close the carton and press the tape on the head of the box to stick. Pull the tape up to the other end of the box. It needs to be tightened in the process of sealing the box, otherwise the seal will not be tight or press the newly sealed tape by hand.
How to use transparent tape cutter, box sealer, packing machine
1. First of all, it is necessary to open the drum of the tape cutter, place the whole roll of tape into the tape cutter, and fix the tape roll with a fixed core.
2. Then pull out the front part of the whole roll of tape and let the tape pass through the gap between the front shaft of the tape cutter and the bottom from the bottom. Please make sure that the sticky side of the tape is facing down in order to make the tape slide smoothly.
3. The next step is to gently pull the small square at the front of the tape, pull down a piece of tape, and then gently pull the blade back to cut the tape. It is common sense that the thicker the tape is, the more pressure is needed when cutting.
4. At the same time, it also has some flexibility, you can tighten or loosen the tension adjustment button on the tape cutter according to your preference, so that you can have your own preference to control the speed of the tape.
How to use the tape packing machine
How to use the tape baler:
1. First of all, it is necessary to open the drum of the tape baler.
2. Put the whole roll of tape into the tape cutter.
3. Fix the tape roll with a fixed core.
4. Pull out the front part of the whole roll of tape and let the tape pass through the gap between the front shaft of the tape cutter and the bottom from the bottom. Please make sure that the sticky side of the tape is facing down in order to make the tape slide smoothly.
5. The next step is to gently pull the small square at the front of the tape, pull down a piece of tape, and then gently pull the blade back to cut the tape.
Operation method of adhesive Tape sealing Machine
The working principle of the sealing machine: turn on the power supply, start the motor, and enter the sealing machine through the transmission belt. When the left and right movements of the sealing machine touch the tape, the left and right movements can complete the sealing actions such as taping, smoothing, cutting and so on.
Operation method
1. Adjust the height of the worktable: loosen the tripod locking screw on the inside of the tripod, pull out the tripod adjustment frame according to the required height, and then tighten the tripod locking screw.
2. Put the box into the conveyor belt and the length is about 1/3 of the length of the box. According to the size of the box, shake the vertical handle, move the lifting frame, adjust the height of the upper movement, and make the upper movement reach the box.
3. In order to make the box cover close, adjust the position of the guide wheel. Release the handwheel, push the guide wheel frame, make the guide wheel close to both sides of the box, and then lock the handwheel.
4. Shake the horizontal handle, adjust the position of the conveyor belt horizontally, make the conveyor belt close together and clamp the box, then take out the box, and then shake the handle to make the conveyor belt lean again. after the adjustment, you can work continuously.
5. Install the tape reel on the belt seat of the upper and lower movements according to the drawing, so that the glue surface is facing the direction of entering the box, and then the glue surface bypasses the guide belt idler wheel, the glue surface bypasses the unidirectional copper wheel, and the front and rear to the top line and the rubber wheel, keep the glue facing the direction of entering the box.
6. Press the power switch and push it into the box. The box moves forward with the conveying belt and automatically completes the action of sealing the carton up and down and cutting the belt through the continuous sealing mechanism.
How to load the adhesive tape in the sealing machine? How to adjust the length?
Sealing machine packing tape
Install the tape on the mandrel of the sealing machine
The tape needs to be pulled out (the adhesive surface of the tape we pull out must face out)
Is to pull the tape around the knurled sleeve in the movement, and then continue to pass the tape through the sleeve.
Continue to wrap the tape around the knurled sleeve after passing through the sleeve
The sealing machine core piercing process is completed by wearing the tape from the black steel inner sleeve, but the final process needs to be paid attention to in the wearing process, and the operator should be careful to seal the cutter to prevent the cutting accident. The specific wearing process is shown in the following figure.
Adjusting the length of adhesive tape of box sealing machine
First of all, put the tape roll of the new sealing machine into the mandrel, as shown in the picture, second, pull out the tape, bypass drum C and then bypass drum B, third, bypass drum D, and finally pass the tape through tape holder E through drum F, as shown in the following figure. In the whole process, it must be noted that the sticky side of the tape must face outward.
2. The tape piercing diagram is shown in the figure:
3. Adjust the orientation of the tape as shown in the figure:
If the tape is not on the centerline of the box, please refer to the following picture: loosen nut B, then adjust the mandrel with a screwdriver, and then adjust the orientation of the tape.
4. Adjust the tape tension as shown in the figure:
By rotating the knob, the speed of the tape coil can be moderate, the nut M8 can be loosened, the front and rear orientation of the screw M8 × 50 can be adjusted, the elastic force of the long tension spring of the pendulum bar can be changed, and then the tension of the tape can be controlled. When the knob is rotated clockwise, the tape tension becomes larger, and vice versa; when the screw M8 × 50 is adjusted forward, the tape tension increases, and vice versa.
This is the end of the introduction about how to use the tape sealing machine and how to use the sealing tape machine. I don’t know if you have found the information you need. If you want to know more about this, remember to collect and follow this site.