Article catalogue:
- 1 、What is the problem of peristaltic pump filling and sealing automatic all-in-one machine without filling?
- 2 、How to debug the invisible CNC slotting all-in-one machine?
- 3 、The function and use of the all-in-one machine
- 4 、Can you install an all-in-one access control machine by card, both inside and outside?
- 5 、Whether the integrated assembly machine can be turned on or not.
What is the problem of peristaltic pump filling and sealing automatic all-in-one machine without filling?
1. The photoelectric position of the lower limit of diving is wrong.
2. the photoelectric damage of the diving limit position.
3. Wrong setting of equipment parameters.
4. The filling quantity of the filling machine is not accurate.
How to debug the invisible CNC slotting all-in-one machine?
Before the machine tool starts, the cutters, nuts and screws must be carefully checked for firmness. If loosening is found, it must be tightened in time.
2. Pay attention to the cutting direction when installing the tool, and do not reverse it.
3. The main tool turns clockwise
4. before feeding and slotting, make sure that the pneumatic device opens and presses the workpiece on the movable push table and against the positioning plate, and the hand is not allowed near the knife edge.
5. When the machine tool fails, the power should be cut off immediately, and the operation should be stopped. Special personnel should be sent to repair and adjust the machine tool, and the machine tool is not allowed to run with disease.
6. Before machining, the material should first check whether there are iron nails, sand and gravel joints on the cutting tools, and stainless steel grooving machines to prevent damage to the cutting tool joints from flying out to hurt people.
7. the power supply of the machine tool must be cut off in cleaning, wiping the lubricating oil and removing the saw blade and knife debris.
8. Machine tools should be operated, adjusted and maintained by designated personnel, and the use of machine tools by people who are not familiar with them is strictly prohibited.
9. Workers should wear earplugs, glasses and other labor protection products when operating.
10. The maintenance of the machine shall be carried out in accordance with the “equipment operation, maintenance and maintenance system”.
Matters needing attention of NC slotting machine
one。 Pre-production should be carried out before production, and several finished products should be checked continuously and confirmed to meet the requirements before formal production. Pay attention to observation in the production process, check the trial production process every five minutes, and stop and adjust immediately if there is a problem.
two。 During the operation of the slotting machine, be careful, buckle the overalls, avoid the knife edge, do not touch the moving parts with your hands, and do not touch the button at will to ensure the safety of production.
three。 Accurately adjust according to the required size, use special tools when adjusting, be careful and pay attention to safety.
four。 Pay attention to and concentrate on working hours, strictly abide by the operating rules, and do safe homework.
five。 The paper feeder should be adjusted to a uniform straight line and parallel to the working axis before work.
six。 Cut off the power supply before adjusting the equipment.
seven。 CNC slotting machines often check whether the parts are worn or do not meet the requirements, and repair or replace them in time if necessary.
eight。 After adjusting the working size, check whether the part that should be locked is locked, whether the chain is loosened moderately, remove all idle items on the equipment, and then manually turn the car to see if there is anything abnormal.
nine。 When adjusting the pit ploughing machine, pay attention to the use of the paper separation knife in a complete set and the appropriate gap and suitable pressure of the pressing wheel.
ten。 Pay attention to machine maintenance and lubrication, ensure the oil level of the oil tank, and often drip. The feeder drive slider is refueled once per shift. Connecting gears are often oiled and lubricated. Running bearings are inspected for half a year to once a year and filled with calcium matrix butter. Adjust the vortex rod to moisten on schedule. All shafts should be kept clean and often wiped with oil. After production, stop the machine according to the designated procedure, and then cut off the power supply. Wipe the machine when you go to work every day, make sure your hands are clean during the work, and clean the surrounding environment as soon as the work is done.
eleven。 Pay attention to the pressure between the chamfering blade and the bottom shaft, gently intercept the blade after contact with the cardboard, and adjust slightly to prevent damage to the knife edge.
twelve。 When the CNC pit ploughing machine starts, make sure that the oil level of the exposed oil cup is right, then start the head to run at a low speed, observe whether the rolling is abnormal, and improve the working speed when each transmission department is completely lubricated and the machine rolls without abnormal noise. Stop the machine immediately in case of failure.
The function and use of the all-in-one machine
1. put the machine on the ground to ensure the safety of the machine.
2. Plug in the power supply and press the switch to ensure the normal operation of the machine.
3. The grinding container is placed on the machine to ensure the safety of the grinding container.
4. Connect the exhaust pipe of the grinding container to the exhaust port of the machine to ensure that the hot air can be discharged normally without harming the machine.
Can you install an all-in-one access control machine by card, both inside and outside?
Yes
Access control all-in-one machine electromagnetic lock glass door magnetic lock fingerprint card swipe password No. 7 double-door glass door [can be opened inside and outside + frameless glass without edge]
Whether the integrated assembly machine can be turned on or not.
1. Does the power supply fan turn on or not?
If the power supply fan does not turn, then do not look at it, it must be a power failure, replace the power supply.
2. Or is there no signal input from the power supply fan to the screen?
If the power supply fan turns and the monitor has no signal, the problem is that the highest to the lowest is the memory, the CPU, the motherboard, and the most likely memory or memory slot. Clean the memory with an eraser, clean the slot with the hairdryer, and continue to test to see if it is all right.
3. If it helps you, I hope to adopt it. Thank you!
This is the end of the introduction of the all-in-one machine. Thank you for taking the time to read the contents of this site. Don’t forget to look for more information about the all-in-one machine manual and all-in-one machine on this site.