Article catalogue:
- 1 、What is the correct operation procedure of the plastic winding machine?
- 2 、Working principle of heating wire winding machine
- 3 、What kind of equipment is the top laminating machine of the winding machine and how does it work?
- 4 、What problems should be paid attention to when using the winding packaging machine?
- 5 、How does the wire harness winding machine AT-101 work? How does it drive? Guys, help! Thank you!
What is the correct operation procedure of the plastic winding machine?
The winding machine not only basically meets the needs of containerized packaging, but also has the functions of keeping the wound goods clean, avoiding dirt and dampness, greatly reducing the cost of the container and improving the efficiency of work. it is widely used in the container packaging of export, glass manufacturing, plastic products, all kinds of dyes and other commodities.
Therefore, how to operate the winding machine correctly has become a very important and prominent problem. The correct operation procedure of the winding machine is as follows:
First, when the winding machine is in the initial state, the film should be fixed on the turntable or the wound object, and turn on the automatic work button.
Second, the turntable is in the working state and changes to the extreme state, which allows the film to output itself as it rotates, then the turntable counts, and when the film reaches the value set at the bottom, the frame rises to a higher level.
Third, when the membrane frame rises to the point where the photoelectric switch button cannot reach the winding object, the delay time is set, at this time the membrane frame does not rise, and the next time is calculated as one time, the turntable is still working, and in counting, when counting the number of winding rings on the top layer set, the height of the membrane frame is reduced until it is reduced to the bottom, and the next time it is calculated again, and starts to calculate the number of winding rings at the bottom.
Fourth, repeat the cycle according to the above steps until the number of times up and down reaches the set value, the packaging process of the winding machine is completely finished. The turntable falls slowly until it returns to the initial state of the winding machine.
Hope to adopt, Suzhou Jiajun Packaging Machinery Co., Ltd.
Working principle of heating wire winding machine
The winding object is placed in the middle of the turntable, and the turntable motor is started to roll, which naturally drives the turntable to roll, so that the object completes the outer winding film machine. The working principle of the heating wire winding machine is to place the wound object in the middle of the turntable, start the turntable motor rolling, naturally drive the turntable rolling, so that the object completes the peripheral winding film machine, winding machine, widely used in foreign trade exports, food and beverages, plastic chemicals, glass ceramics, mechanical and electrical castings and other products assembly cost, can prevent the damage of goods in the handling process, and play the role of dust-proof, moisture-proof and cleaning.
What kind of equipment is the top laminating machine of the winding machine and how does it work?
The ordinary winding packaging machine can only winding the four sides of the goods, and the top and bottom generally can not be wound and packaged at the same time. The emergence of the laminating machine has effectively solved this problem. Suzhou Jiachuang
When in use, the equipment of the top laminating machine places the film roll on the film discharge roller of the lifting frame, raising the lift to the working height, and the film discharge roller rotates through the RV50 reducer and the sprocket chain, thus making the film roll rotate and discharge the film. The film clamps the film through the action of cylinders 1 and 2. Then the RV40 reducer of the conveyer frame starts to run, and the sliding unit is driven by the sprocket chain transmission mechanism to transport the film forward. when the sliding unit carries the film to the other end of the frame, the cylinders 3 and 4 begin to clamp the end of the film. At this time, cylinders 1 and 2 move to release the transmission film, quickly return to the original position before work, and tighten the film transmission, and then, the hot break film cylinder 5 and 6 move downward at the same time to break the film, and then the cylinder 3 and 4 relax the film transmission, and the film is covered on the top of the article. The film is covered for the next cycle.
What problems should be paid attention to when using the winding packaging machine?
Hello, you should pay attention to the following questions
1. First of all, the customer must read the operating instructions of the equipment carefully before operation, , and then install and debug the equipment. 2. The pallet winding machine should be installed in a drier indoor environment where there is no dust, explosive chemical agents and other substances that corrode the machine and other substances that corrode the machine. The temperature range is between-10 ℃ and 50 ℃ without frosting in the environment. 3. It is forbidden to test the voltage between the current motor control board, magnetic powder brake control board and PLC input point and ground wire. 4. When the machine is in normal use, regularly check whether the connecting parts of the machine are loose or fall off, if so, be sure to fasten. It is strictly forbidden to move or remove the upper and lower fixed limit blocks! 6. The machine turntable should run clockwise. 7. It is strictly forbidden to stand people or stack any objects under the winding system. 8. When the winding system rotates, it is strictly forbidden to extend your hand inward or into other objects to prevent damage to cots or fingers. 9. When the machine is running, the operator should stand in a safe place at a certain distance from the turntable. When the machine is completed and stopped, it is necessary to approach the machine to prevent damage. If necessary, a safety net should be installed. 10. it should be firmly grounded or connected to zero to prevent leakage from damaging the machine or personnel.
How does the wire harness winding machine AT-101 work? How does it drive? Guys, help! Thank you!
It is controlled by single-chip microcomputer, the driving power is a stepper motor, and the speed can be set. The motor is driven by a tooth belt to drive an open turntable, the tape is fixed on the turntable, the tape rotates, the wire harness is fixed, and the winding is carried out by manual dragging. Tape cutting is also done by hand. The latest model has installed a plexiglass shield on the rotating body, which is very beautiful.
This is the end of the introduction of the working video of the winding machine. Thank you for taking the time to read the contents of this site. Don’t forget to look for more information about the operation manual and video of the winding machine on this site.